(mm) 寸法公分 |
6级 (h6) |
7级 (h7) |
8级 (h8) |
9级 (h9) |
10级 (h10) |
11级 (h11) |
12级 (h12) |
13级 (h13) |
1.0~3.0 | +0 -0.006 |
+0 -0.010 |
+0 -0.014 |
+0 -0.025 |
+0 -0.040 |
|||
3.01~6.0 | +0 -0.008 |
+0 -0.012 |
+0 -0.018 |
+0 -0.030 |
+0 -0.048 |
+0 -0.075 |
+0 -0.120 |
+0 -0.180 |
6.01~10 | +0 -0.009 |
+0 -0.015 |
+0 -0.022 |
+0 -0.036 |
+0 -0.058 |
+0 -0.090 |
+0 -0.150 |
+0 -0.220 |
10.01~18.0 | +0 -0.015 |
+0 -0.018 |
+0 -0.027 |
+0 -0.043 |
+0 -0.070 |
+0 -0.110 |
+0 -0.180 |
+0 -0.270 |
18.0~30.0 | +0 -0.021 |
+0 -0.033 |
+0 -0.052 |
+0 -0.084 |
+0 -0.130 |
+0 -0.210 |
+0 -0.330 |
|
30.01~50.0 | +0 -0.025 |
+0 -0.039 |
+0 -0.062 |
+0 -0.100 |
+0 -0.180 |
+0 -0.250 |
+0 -0.390 |
|
50.01~80.0 | +0 -0.032 |
+0 -0.048 |
+0 -0.072 |
+0 -0.150 |
+0 -0.190 |
+0 -0.300 |
+0 -0.470 |
- h6 精度研削品
- h7 标准研削品
- h8 高精度引拔品
- h9 标准引拔品
- h10 异形引拔品
◎ 此表公差不适用于铜棒二端100mm以内距离。
This table shall not be applied to within 100mm length from both bar ends.
◎ 偏径差(真圆度)为公差之30%以内。圆筒度为公差之50%以内。
Deviations in diameter(roundness) shall be within 30%of the tolerance .Deviations shall be within 50% of the tolerance.
◎ 特殊尺寸公差可由买卖双方协议。
Ohter special size tolerance may be satisfied on request.
制品长度(mm) (公差) |
长度制品 | 长度公差 | 特 欢 殊 迎 长 定 度 制 |
|
引拔制品(D) | 2100~4000 | +20-0 | ||
研磨制品(G) | 2100~4000 | +20-0 |
真直度(mm) (公差) |
快削钢 | 特殊钢 | 特 殊 制 品 (0.3以下) (0.6以下) |
||||
引拔制品 | 研磨制品 | 引拔制品 | 研磨制品 | ||||
标准法则 | L=1000 | 0.7 | 0.5 | 1.0 | 0.7 | ||
高精度制品 | L=1000 | 0.4 | 0.3 | 0.6 | 0.5 | ||
L=400 | 0.08 | 0.06 | 0.15 | 0.1 |
◎
此表l=400仅适用于5.0~16.0mm圆棒。l=1000仅适用于8.0~16.0mm圆棒。其余尺寸另议。
l=400 is applied to the round bar of dia.5.0~16.0mm. l-1000 is applied to the round bar of dia.8.0~16.0mm.
Straighrness for other sizes may be specified when agreed upon between the manufacturer and the purchaser.
表面粗度 (公差) |
寸法(mm) | RZ(10点平均粗度) | Rmax(最大粗度) | |
标准研磨制品 | 1.0φ~5.0φ | 2.5 | 3.2以下 | |
标准引拔制品 | 2.0φ~6.0φ | 5.0参考值 | 10.01~20.0 | |
6.1φ~10φ | 2.5参考值 | 10.0以下参考值 |